inflatable boat repair information and procedures about gluing and fabrics (2022)

Inflatable BoatsRepair and Restoration Paint

Turn your old inflatable
into a renewed gem!

View These IncredibleResults

Back To Informationand Advice Mainpage

Inflatable Boat Basic Repair Information and Procedures

(Video) How To: Inflatable Repair Adhesives Guide

Small repairs and the addition of small accessories may be attempted by the owner if factory gluing instructions are followed closely.

Rips or holes larger than one inch in the air chambers or within two inches of a seam should be repaired with internal and external patches by a professional repair technician at a certified repair facility. A quick patch repair may solve your problem for a short period of time, but we recommend you have it redone by a professional.

We recommend that major repairs and the addition of large accessories such as oar locks, seating or towing rings be done by a professional repair technician at a certified repair facility.

If your boat is still under warranty and you are experiencing a seam failure; the wooden transom separating from the molded transom flanges or tubeset; or the fabric is turning yellow and sticky, call your dealer immediately. Defective seams or sticky fabric may result in complete warranty coverage and you may receive a new boat for free or at a small prorated fee.

If you plan to attempt a small repair, please follow these instructions closely:

Repair kits, glue and more.

Great products to repair and protect your inflatable boat. Or consider a new boat.

Repair kits, glue and more.

Inflatable Boat Repair Paint
Keel Guard Protector

inflatable boat repair information and procedures about gluing and fabrics (7)
Is your old boat beyond repair? Buy a new one a low prices.


ESSENTIAL INFORMATION FOR USING ALL GLUES AND ALL FABRICS

LOW HUMIDITY AND TEMPERATURE CONTROL

  • Relative humidity must be less than 70%, preferably as low as 40%.

    (Video) ORCA® RIB Gluing and Manufacturing process

  • Temperature 64° to 77°F.

    Never fiddle around with these. Bond strength drops very rapidly with heat or high humidity. Take your boat indoors. Don't even think about trying to glue on the dock or near the water or in direct sunlight. Professionals use a specially built, climate controlled room, and still don't attempt to work on a rainy day.

    Note: You are using a two-part contact cement. The solvents in the glue must evaporate before assembly. When ready to assemble parts, the glue must not be tacky at all to the finger. It must not have spots of whitish glaze. If so, you may have spread the glue too thick, not waited long enough between coats, or a sudden drop in temperature or gust of humid air may have occurred. Someone may have opened the door, or you may have leaned too close and breathed on it. Plan to stay in the room until finished.

GENERAL TIPS

  • Mark out your patch or accessory perimeter where it will be glued on. Then use masking tape to tape off the area to ovoid getting MEK or glue on other parts of your boat during the repair process. This takes a little time but is well worth it in the end as the glue is hard to get off the boat after it dries and looks very messy when it dries and goes brown from the sun.

  • If using small cans ( 1/4 L) mix the entire can with the dose of accelerator. Inaccurate measurement will weaken the glue. Once opened the accelerator cannot be kept. Do not try to save it. The quality of your final bond depends on it.

  • Apply glue with a paint or glue brush with the bristles cut short (1/2 to 3/4") so they are stiff. It must be natural hair (i.e. OK for lacquer); bound in metal not plastic; preferably with wooden or metal handle. Careful not to get glue on areas of your boat besides the repair area.

  • Old glue must be completely removed -- solvent, sandpaper, scraping, grinding with a Dremel tool. Glue will not stick to old glue. Clean it off thoroughly. Be careful not to burn or melt the fabric if using a Dremel tool. Constant motion with the tool will prevent this problem.

    (Video) How To: Inflatable Boat Repair to Patch a PVC Inflatable Dinghy or RIB

  • If your boat has ever been protected with ArmorAll® or another silicone or petroleum based product, you may have great difficulty getting a bond. Wipe the repair area well with MEK, follow the gluing instructions closely and hope for the best.

  • Pinhole size leaks in most Hypalonfabric or PVC boats sometimes may be repaired simply by use of either Seam Seal or Air Seal liquids. You might be able to avoid a patch on the boat.

  • To find tiny leaks, take floor boards out, inflate boat hard. Put some liquid detergent in a bucket of water and with rag or big wash brush, scrub it all over boat. Keep watch for elusive, tiny bubbles. When you find the first leak, keep looking. You might as well fix them all at the same time! Remember, the number one cause of slow leaks is a poorly seated valve. Unscrew, clean. Make sure little rubber O-rings are good. They are the cheapest repair possible.

  • If patching, cut patches 1 to 2 " larger than tear in each direction and round the corners (a quarter makes a good template for the edges). Little one inch circles pasted over a pin hole won't last. Try to get the same fabric used by the manufacturer for your boat. The inside and outside surface may be different. If you can't match color, sometimes a cleverly shaped patch in contrasting color can be made to look like decoration instead of a Band-Aid. e.g. arrow, lightning bolt, even a new D ring if in right spot. Professionals often put one on each side to look like they came with the boat.

  • Inflate boat to apply accessories. Deflate to patch air leaks, even if very small. Air pressure will bubble the patch before glue sets.

  • Use our inflatable boat restoration paint if your boat is old looking, looks faded, is sticky or generally looks old and ugly.

BE SAFE

  • Do Not Smoke! Glues and solvents are flammable. No open flames (e.g. furnace or pilot light when working in a cellar.)

    (Video) How repair an inflatable boat puncture - best practice

  • Use in a well ventilated area. Fumes can be overwhelming. A carbon filter respirator is recommended. MEK solvent smells, but is relatively safe. It is recommended that you not use Toluene - the factories do but it is quite dangerous.

  • Accelerator (small bottle) is toxic. If spilled on on your skin WASH IMMEDIATELY with soap and water. If in your eyes, IMMEDIATELY FLUSH WITH WATER for at least 2 minutes and consult a physician. (Accelerator is an isocyanate based product.)

  • Always wear safety gear as recommended by the manufacturer of glue, solvent, accelerator, etc.

NOTE: These instructions are offered to assist you in home use of glues. Because of the wide variety of conditions and critical procedures, we. assume no responsibility for failure of glued bonds or any consequence thereof. We always recommend repairs be done by trained professionals. If you mess it up, it's costly time to clean the fabric and rectify the problem and it can greatly exceed the cost of the original repair.


PVC fabric Gluing Instructions (Most modern Zodiac brand boats are PVC) Here

Hypalon Fabric Gluing Instructions Here

Fabric Differences
A quick discussion of the differences between "PVC" and "Hypalon" (rubber) fabrics.

(Video) How To: PVC and Urethane Boat Repair

FAQs

How do you repair an inflatable boat? ›

How To Repair an Inflatable Boat or Inflatable Kayak - YouTube

What glue can you use on inflatable boat? ›

Use 2 part Polymarine 2990 Hypalon Adhesive. To glue PVC tubes to GRP hulls. First the Hull will need to be lightly sanded to key the surface and solvent cleaned with 2903 PVC solvent cleaner surface primer. Second, apply '2990 Hypalon' adhesive as the important primer on the hull (to take the PVC adhesive later).

How do you repair an inflatable? ›

Repairing Inflatable Pin Holes, Punctures, and Tears - YouTube

How do you glue inflatables? ›

Inflatable Boats: How to Glue on a Patch (2020) - YouTube

How do you glue an inflatable boat handle? ›

Inflatable Boats: Gluing on an Extra Handle (2020) - YouTube

How do you repair an inflatable boat bottom? ›

How To Repair Inflatable Boat DIY with simple tools - YouTube

How do you glue accessories to an inflatable boat? ›

We recommend Polymarine 2-Part PVC adhesive. This glue will provide a stronger, more permanent bond than 1-Part adhesives and works well with our boats. A 2-Part PVC adhesive is highly recommended with accessories that will be under considerable load.

How do you remove old glue from inflatable boat? ›

Removing glue from PVC inflatable boat - YouTube

What glue is good for vinyl? ›

Polyurethane glue is ideal for gluing thinner flexible vinyl together as well as gluing vinyl to other surfaces like wood or plastic.

How do you repair an inflatable vinyl? ›

Patch a Damaged Inflatable using a Vinyl Cement Repair Kit - YouTube

Can you use super glue on inflatables? ›

How to make a Quick Inflatable Boat Repair - YouTube

How do you repair an inflatable Hypalon boat? ›

How To: Patch a Hypalon Boat - YouTube

How do you repair glue that is grounded? ›

By right-clicking on an armor piece (or accessing its menu with the appropriate button) players will be able to select the repair function from a dropdown menu. This will then show players what type of glue is needed to fix it up.

How long does PVC boat glue take to dry? ›

Using a brush applicator apply an even thin coat of adhesive to both the back of the external tube patch and the masked repair area. Leave to dry for at least 20 minutes.

Does Flex tape work on inflatables? ›

A: The Flex Seal Inflatable Patch and Repair is an easy to apply one-step solution consisting of self adhesive, strong, rubberized, crystal clear patches that are designed to instantly seal air leaks in all types of PVC plastic inflatables.

How do you fix a hole in an inflatable seam? ›

Invisible Seam Repair on an Inflatable Toy - YouTube

How do I fix a leaking inflatable boat valve? ›

How To: Find and Fix Inflatable Boat Valve Leaks - YouTube

inflatable boat repair information, repair procedures and steps, fixing inflatable boats, inflatable boat accessories, inflatable boat

Glue: Zodiac #7097 Universal Glue; Polymarine. Urethane (PVC) Glue.. Preparation: Gather rags, glue brush; solvent; timer with. second hand or stop watch; make sure all the old glue is cleaned off;. get your patch cut out,. position noted and marked.. Mix accelerator and glue thoroughly either now or while. waiting between the solvent wipes below.. Solvent. Cleaning (3 times - to prepare the fabric for a chemical bond with the. glue). Wait five minutes (timed) If glue still looks wet, wait longer.. If over 10. minutes or if glue has spots of white haze the glue has picked up. moisture and you should try to "reactivate" it.. With a clean rag wet the glue surface with MEK but do not rub the glue off (one. quick swipe).

inflatable boat repair information, repair procedures and steps, fixing inflatable boats, inflatable boat accessories, inflatable boat

Solvent. Cleaning (2 times - to clean the fabric for a strong "mechanical bond" with. the glue). Scrub both sides (boat and patch or accessory) with MEK on a rag. to clean surface.. Wait 10 minutes after the first MEK wash. (time it). Apply one more solvent wipe with 10 minute waiting time (timed). between them.. You are cleaning the fabric for glue adhesion.. Glue. Application (2 thin layers 20 minutes apart). Wait 20 minutes (timed) If glue still looks wet, wait longer.. Wait 10 minutes after second layer of glue.

Small repairs and the addition of small accessories may be attempted by the owner if factory gluing instructions are followed closel...

Small repairs and the addition of small accessories may be. attempted by the owner if factory gluing instructions are followed closely.. Or consider a new boat .. LOW HUMIDITY AND TEMPERATURE CONTROL. • Relative. humidity must be less than 70%, preferably as low as 40%.. Glue will not stick to old glue.. Deflate to patch air leaks, even if very small.. Always. wear safety gear as recommended by the manufacturer of glue, solvent,. accelerator, etc.. We always recommend repairs be done by trained. professionals.

When it comes to your best yard inflatables, placing them outside inevitably puts them in harms way for potential damage. It could be anything from wild animals to a bad snow storm that could cause your inflatable to break, leaving you with an expensive pile of fabric on your lawn and not much else. There’s […]

There’s no need to worry about buying a replacement though, as most issues with your inflatable not working can easily be fixed.. The ProblemThe FixProduct Image Fabric or Nylon Tears Transparent Duct TapeTear-Aid Patch See-Thru Vinyl Tear Tear-Aid Patch Blower Broken Replacement Blower Inflatable Falling Over Ground Stakes Does Your Inflatable’s Blower Work?. The first step you’ll need to do is figure out if your yard inflatable’s blower is working.. Plug your inflatable directly into an outlet , bypassing any outdoor inflatable timers you may be using.. If your blower is working, but the inflatable isn’t inflating all the way, you likely have a tear in your fabric .. Most yard inflatables are made of a fabric/nylon material that can be repaired in a variety of ways.. If those steps fail, sad to say you need to look into replacing your inflatable blower.. Your existing inflatable blower may have an LED plug attachment in it if it has internal LED lighting.. One other workaround for your broken blower blues is swapping fans with another inflatable that does work.. For example, if you have a Valentine’s Day inflatable with a worker blower and an Easter yard inflatable without, you can swap the working blower between the two once the seasons change.. This may require you to buy a new yard inflatable, but that can often be cheaper than buying a replacement blower alone.. You may be wondering if it’s possible to replace or fix the LED lights in a yard inflatable.

Inmar Marine Group U.S.A., is the proud manufacturer of Inmar Inflatable Boats. Our products are used by Marine professionals worldwide. Inmar specializes in Inflatable Boats for Diving, Military, Rescue and Yacht tenders. Inmar is able to offer quality packaged performance for the Boating Professional. Located in San Diego, California, Inmar Marine Group provides quality sales and service worldwide.

Preparation: Gather rags, glue brush; solvent; timer with second hand or stop watch; make sure all the old glue is cleaned off; get your patch cut out, position noted and marked.. It always leaves a neat tidy finish if you tape off the perimeter of the patch area with masking tape to avoid over glue.. Mix accelerator and glue thoroughly either now or while waiting between the solvent wipes below.. Solvent Cleaning (3 times - to prepare the fabric for a chemical bond with the glue). Scrub both sides (boat and patch or accessory) with MEK on a rag to clean surface.. Be careful not to wipe the MEK on areas of the boat or patch that will be seen as MEK will make the fabric sticky and shiny.. Wait 5 minutes after the first MEK wash. (time it). Mix glue and accelerator while waiting, if not done already.. Apply two more solvent wipes with 5 minute waiting time (timed) between them.You are preparing the fabric for glue adhesion.. For davits and hard based accessories, deflate boat and press through from other side to make sure of adhesion.. If so, you may have spread the glue too thick, not waited long enough between coats, or a sudden drop in temperature or gust of humid air may have occurred.. Then use masking tape to tape off the area to ovoid getting MEK or glue on other parts of your boat during the repair process.. Careful not to get glue on areas of your boat besides the repair area.. Glue will not stick to old glue.. Deflate to patch air leaks, even if very small.

Quick and easy fix-it tips for inflatable boats

Before we look at the care and repair of your inflatable, you need to know about the materials and construction of your inflatable.. The majority of all inflatables used for boating consist of a substrate and a coating: the substrate provides the strength and the coating provides the waterproofing.. Before attempting any repair on your inflatable, you must know what type of materials you are repairing, because the glues that bond to Hypalon, for example, will not work on a PVC material.. On a regular basis, you need to rinse out your inflatable, because the nemesis of every inflatable boat is sand and grit.. Do not ever use a silicone sealant to patch your inflatable, and stay well away from silicone-based coatings such as Armorall which, though they make your inflatable shiny, will prevent patches from ever sticking to the hull.. Leaks in your inflatable are likely to come from one of four sources: punctures, wear, porosity, or valves.. It doesn't take great skill to repair a puncture or tear using a inflatable repair kit, although experts suggest that any tear longer than about four inches should probably be tackled by professionals.. These leaks can be patched at first, but porosity is an indicator that it's time to replace your inflatable.. Avoid generic inflatable repair kits and rely on kits from the manufacturer of your raft, which can be found at most marine hardware stores or your inflatable dealer.. If you find yourself in a remote area without an inflatable repair shop, check at the local airport where you may find someone who services aircraft life rafts.

Inflatable boat paint advice and dinghy paint for restoring inflatable Boats. This inflatable boat paint repairs and restores inflatable dinghies to new while saving you money.

Easy to apply - clean the boat, brush on basecoat and topcoat in stages, let dry and cure, and go boating!. Restores your boat - restores old, faded, sticky inflatable boats to looking renewed with enhanced protection and appearance.. Each " Pontoon & Floor Kit" - covers the respective inflatable boat length and outer floor (the side of the floor that is in the water), in the color specified.. Should I restore or replace my inflatable boat?. Repair major leaks first before you begin restoring your inflatable boat.. Hypalon. - Seams on hypalon boats are glued.. PVC - Seams on PVC boats are heat welded.. You are anxious to restore your inflatable boat with Tuff-Coat but the most important step in achieving excellent results is CLEANING!. Cleaning Rubrails I was recently asked by an inflatable boat owner how to clean the rub rails on his inflatable boat.. Often in a restoration project, the rub rails, which protect the boat pontoons from abrasion, look as tired and worn out as the boat material.. Tuff-Coat boat paint is NOT to be applied to these rub rail areas.. If you can paint, you can use Tuff Coat In order to restore your inflatable boat, you don’t have to know anything about a whole lot of stuff, except how to paint.. Using Tuff-Coat, almost anyone can take a worn inflatable hypalon boat and make it look like new again.. Tuff Coat can restore virtually any kind of damage your hypalon inflatable boat may have suffered.

Do you know? Inflatable boats have been in use ever since 880 BC! From then to now, they have gone through a radical change in terms of design, material, and method of manufacture. Read on to know all about inflatable boats!

A range of inflatable boats is available including rubber rafts, inflatable kayaks, lifeboats, and rescue boats.. There are several leading boat manufacturers in India that design and manufacture inflatable boats, SHM Shipcare is one of them.. Specs: L: 4.2m, W: 1.8m, Colour: Orange It has a full load capacity of 6 pax, which includes 5+1 stretcher.. It is a material with an excellent capacity for holding air, which makes it a great option for inflatable boats.. Due to these reasons, SHM uses Hypalon or Neoprene fabric in the construction of its inflatable boats.. Hypalon is highly resistant to chemicals.. Inflatable Hypalon boats will not deteriorate with time and these boats will be extremely durable, with a span of at least a decade.. Regardless of the material used to build an inflatable boat, it is necessary to carry out routine maintenance and repairs and ensure proper care of the boat.. SHM Shipcare provides a range of services for the maintenance of Rigid and Inflatable Boats.. Inflatable boats made of PVC and Hypalon are the two most common and easily available options of fabric.. SHM Shipcare uses Hypalon to make inflatable boats due to its durability and strength of Hypalon.

Inflatable boats are convenient to use and are super easy to repair if you have the right know-how. Find out all about their repair and maintenance procedures right here!

It is necessary to clean an inflatable boat after each use.. After the boat is rinsed with water, ensure that the water does not stay on the surface of the boat.. The drying process is the most important one because if the boat is stored without the water being cleaned off its surface, it becomes susceptible to mold.. To repair an inflatable boat, it is first necessary to know the type of material it is made of, so as to use appropriate tools and measures.In ordinary cases,to manufacture the inflatable collars and tubes of boats, three main types of materials are used: Hypalon, Polyvinyl chloride (PVC), and Polyurethane (PU).. For Hypalon fabric boats, a suitable adhesive should be used.. Small tears can be repaired with a single fabric patch, but the larger patches need fixing both from the inside and the outside of the tube.. Glue PVC patch to Hypalon tube –. After cleaning the patch, apply one coat of adhesive to the side that is to be glued.. Glue Hypalon patch to PVC tube –. After abrading and cleaning the patch with solvent as told in step one, apply a coat of Hypalon adhesive to the back of the patch.. As required during the repair of inflatable boats, the environment where the valve is to be replaced must be stress-free, relative humidity less than 60%, temperature between 18°C and 25°C.

Properly maintaining your inflatable boat can be vexing, no? Wait a sec, though, before throwing up your hands and marching off in search of a bottle of rum.

Look for detached fabric or accessories.. Feel the tubes to get an idea what kind of shape they’re in.. No leaks?. In addition to these “no-no” products, there are a number of practices you’d do well to avoid.. Strange as it may sound, your inflatable actually likes being inflated.. While inspecting your dinghy for wear and tear, why not give it a good cleaning as well?. If you’re trying to put a Hypalon patch on a PVC boat, or a PVC patch on a Hypalon boat, your attempt will fail.. Be good to your inflatable dinghy and it will be good to you. Another cause of DIY disasters is repair shops that put out shoddy work.. “Before” and “after” photos will give you a good idea of the types of repairs such a facility is capable of performing.. Once you’ve decided on a repair shop, be sure to ask the tech there about his or her processes and policies.. But again, even if you find yourself working with a shop that charges more than I do, in the long run, it’s worth it.

Advice on how to make your tender last from a RIB repair specialist.

An expert at tube repairs can give your inflatable or RIB a breath of fresh air.. Inflatables and their cousins, RIBs (Rigid Inflatable Boats), look pudgy, but they can take a heck of a lot of abuse, and most of them do: Inflatable tenders are bounced against barnacled pilings, dragged onto rocky beaches, jammed into a gaggle of other tenders at dinghy docks, flung around at the hands of reckless kids, overloaded with crew and supplies, capsized while being towed and filled with soapy water to wash clothes after a long ocean passage.. I believe them: When I visited the shop, the Goings were working on projects from small inflatables leaking air to a 20-foot-plus RIB needing complete tube replacement, with a bunch of other boats waiting their turn.. In those cases, the Goings will have custom tubes built—their supplier can fabricate new CSM tubes for any RIB by taking a pattern from the original tubes.. Some RIB builders (Zodiac is one) attach the tubes with a track-and-bolt-rope arrangement: The bolt rope, basically a synthetic rope with fabric folded around it, is glued to the tube using a high-bond, two-part adhesive formulated to stick like a barnacle; there are different adhesives for CSM and PVC.. For example, Star brite says their Inflatable Boat & Fender Cleaner can restore the appearance of dirty RIBs and inflatables, removing grime, grease, fish blood and so forth.. After cleaning, UV-protect the inflatable tubes once a month, again with a product specifically designed for inflatable boats.

Learn how to properly care for your raft, cataraft or inflatable kayak. We include basics about mounting frames, cleaning instructions and repairs.

All NRS boats with inflatable floor (self-bailing) have a second valve called a pressure relief valve (PRV).. The rubber valve seal in the bottom of the valve stem is the most important part of the valve to clean.. If a B7 fill valve will still not hold air after the cleaning recommended above, you need to unscrew the valve to check the inside of the valve.. With the tube inflated, turn the valve wrench counterclockwise to loosen the valve, then deflate the tube.. With the tube inflated, loosen the valve by turning the valve wrench counter-clockwise, then deflate the tube.. The rubber valve seal pops onto the expanded tip at the base of the valve stem, so it is simple to replace the whole valve stem assembly.

This article will go over the differences between PVC and CSM and what to expect from them.

Inflatable boats can last anywhere from 2-25 years, primarily depending on the material they are made of, and how they are cared for!. Most PVC dinghy issues are due to the owner treating it like a Hypalon boat and letting it bake in the sun, instead of giving it the proper care PVC requires.. Welded PVC boat will outlast those made with glues/adhesives Hypalon (CSM) boats usually last 7-15 years, but can last as many as 20 years. In the early days of this technology, PVC was very rigid and brittle, making it fragile and difficult to work with.. Using various additives, PVC fabric has been significantly improved from the brittle material it once was, to become one of the most versatile synthetics on the market.. Since PVC inflatable boats were still new to the market, manufacturers were still experimenting with their construction and durability.. At first, PVC boat seams were using glue, similar to how Hypalon dinghies are made.. The PVC material today uses various additives that have dramatically improved the fabric and PVC inflatable boats.. A high quality, well cared for inflatable can be expected to last anywhere between 5-10 years.. Boats that use hot air welding will have longer lasting seams, but the accessories and the transom will not be able to withstand the climate unless the boat is stored in a temperature controlled environment.. Proper Care and Extending the Life of Your Dinghy With every product, there is a recommended way to care for it and help ensure it stands the test of time.. There are several products available that can help protect PVC fabrics.. Another product that can prolong the life of your dinghy is inflatable boat antifouling paint.. Cleaning them will help prolong the life of the fabric and the glue.

inflatable boats, rib, dinghy, dinghies, dingy, pvc fabric repair, pvc repair

Preparation: Gather rags, glue brush; solvent; timer with second hand or stop watch; make sure all the old glue is cleaned off; get your patch cut out, position noted and marked.. Solvent Cleaning (3 times - to prepare the fabric for a chemical bond with the glue). Scrub both sides (boat and patch or accessory) with MEK on a rag to clean surface.. Be careful not to wipe the MEK on areas of the boat or patch that will be seen as MEK will make the fabric sticky and shiny.. Wait 5 minutes after the first MEK wash.. Apply two more solvent wipes with 5 minute waiting time (timed) between them.. Apply a thin glue layer with stiff brush to both sides.. Careful not to get glue on areas of your boat besides the repair area.. Glue will not stick to old glue.. Deflate to patch air leaks,. even if very small.. (available at veterinarian and feed stores) Place the needle through the puncture hole.. Most of the time the boat must be inflated so that the inside of the boat is not glued together, or that the needle punctures the other side of the boat.. It is important that the glue be allowed to puddle up around the hole so that air pressure can force the glue out of the hole and help seal it up.. Be careful to hold the needle and syringe together as the plunger is operated.

Though most of today’s inflatable towables are made from heavy-duty PVC and Vinyl materials, they are bound to get punctured or damaged at some point, either due to improper inflation or normal wear and tear. When that happens and your towable falls outside the warranty period, you might need to figure out ways of fixing

If that’s the case, you need to blow them out using an air pump or if necessary, replace the valve completely.. If there’s any hole or leak on the tube, you’ll see soap bubbles form around the spot.. You can continue checking the rest of the tube surface to identify any other possible leaks.. If you are repairing an inflatable boat made from PVC fabric, you’ll need the following materials:. The kits are always available for both PVC and vinyl materials.. Steps for Repairing Small Holes in an Inflatable: Clean the repair area using water (preferably warm) and mild soap.. Let it air dry for about 5 to 6 hours.. Leave it for 24 hours for the adhesive to dry properly.. Steps for Repairing Large Holes in an Inflatable: If you’re dealing with large holes, you’ll need a PVC or vinyl patch.. Smear or brush a thin layer across the surface of the patch and over the area that needs repair Allow the patch to dry for close to 5 minutes till it’s tacky before positioning it on the inflatable Carefully put the patch onto the damaged area or section of the inflatable Work from the center to the outside of the edges of the patch by pressing down and sliding the smoother to create a seal Set a heavy object, such as a landscaping stone, on the patched area to ensure it dries perfectly Leave the adhesive to dry for a minimum of 24 hours. So taking proper care of your inflatable is the surest way of avoiding any repairs.. Do you know other ways to repair a towable?

Inland Marine USA's quality patch kits, sealant, liquid rubber and topside paint will have your inflatable boat or dinghy looking like new again using our easy instructions.

Inland Marine USA provides Patch Kits for either Hypalon or PVC boats.. We make our Sealant for this repair.. This sealant forms a bond with the interior fabric of the inflatable, stopping or "sealing" slow leaks and preventing future leaks from developing.. And Inland Marine USA Sealant can be used multiple times, so if your inflatable develops a new leak weeks or years from now, you can use the sealant again!. Kevlar can stop bullets; a 2 mil thickness of Inland Marine USA Sealant can stop air up to 90 PSI.. The product is used by professional raft repair companies, US Navy Seals, and individuals like you for inflatable boat repair.. You may not want or need to paint your inflatable after you use Liquid Rubber to re-skin it.. However, if you do want to paint it, you should use Inland Marine USA’s Top Side Paint.. Elasticity is important when painting an inflatable boat and Inland Marine's Top Side paint exceeds these requirements.. Inland Marine USA provides Top Side Paint in seven (7) colors so you can paint your boat, or creatively make it unique and easier to find when in a busy port of call.. Inland Marine USA Top Side Paint. HUMIDITY CAN SERIOUSLY AFFECT THE QUALITY OF PATCHES, PAINT, LIQUID RUBBER AND LIQUID TEAR REPAIR PRODUCTS.

Keep your boat looking like new these simple steps. In this maintenance guide, we’ll cover cleaning & storage tips to keep your RIB boat in excellent condition!

In this guide to rigid inflatable boat maintenance, we’ll cover what to do after a day on the water, as well as long-term maintenance and storage tips.. Especially if you use your RIB in saltwater, thoroughly cleaning it after a day’s use will keep your boat looking nice.. Here’s how to clean your RIB.. Cleaning the RIB isn’t the same as a traditional boat, mainly because of the inflatable siding material.. Be careful to not use these potentially damaging products on your RIB:. Wipe any water spots and debris from your electronics and dashboard instruments and cover them to prevent damage.. Put It Away Dry: Never leave wet areas in your RIB or any boat that you plan to store for a long time.. Check Your Hull: It’s best to check your hull for damage and imperfections when you take your RIB out of the water.. The heat can interact with the inflatable siding and cause deformations and damage.. Also, avoid storing your boat on deck with a dark cover where it will heat up quickly in the sun.. Wash Down the Brakes: Especially if you used your trailer to launch your boat in saltwater, wash the saltwater off the brakes before storage, so corrosion doesn’t cause them to seize.. If your trailer lights aren’t working after long-term storage, try using a contact cleaner on your electrical connections.. If you stay on top of your waxing, it protects the function and appearance of your hull.. Or you can take your boat to a marine mechanic, and they’ll quickly service your engine for you.. Learn where the anodes are on your outboard engine and replace them when they’re starting to look corroded.

How to select PVC fabric for inflatable boat and produce of the PVC boat? The fabric for inflatable boat have many types, also it can be finish by welding or

How to select PVC fabric for inflatable boat and produce of the PVC boat?. In the production of inflatable boats, several basic materials are used: reinforced and non-reinforced PVC materials, rubberized fabric, polyurethane, hipalon and neoprene.. Owning your own boat or boat is not cheap, but there is an alternative: a PVC inflatable boat.. PVC boats were significantly superior to rubber boats in terms of performance, but at first they cost much more than rubber boats.. Today, PVC inflatable boats have become the most popular type of boat of all.. The seams of PVC boats are much stronger and more aesthetically pleasing than the seams of rubber boats.. And despite the reinforcement of the seams with tapes, the strength of the seams of a rubber boat is still worse than that of a PVC boat.. The tensile strength of the seams in a PVC boat is 3.5-4.5 kg., in the seams of a rubber boat 0.5 kg.. PVC boats are lighter than rubber inflatable boats.. PVC fabric manufacturers produce more than 20 colors and shades of their fabrics, which allows PVC boat designers and builders to create beautiful and aesthetically pleasing boats for every taste of their customers.. PVC boats are considered safer, even in the event of a boat cylinder puncture, the air from the PVC boat cylinder leaves much more slowly, leaving the boat owner more time to take measures to save the boat and property in the boat.. If the performance of the boat and its stability on the water are of great importance to you, try to test the model of your future boat by taking a boat of the same model from your fellow fishermen and trying it on the water.

Videos

1. XS Ribs: How to Repair Glue PU Polyurethane, Hypalon Inflatable RIB Boat Fabric Tube Collar TORNADO
(XS Ribs & BMC Ltd)
2. Fabric Hull Floor Repair Installation On A Zodiac Boat
(GasHopper Inc)
3. INSIDE PATCH comprehensive SEAM REPAIR for PVC and Urethane Boats
(Montana River Sports)
4. Inflatable Boats: How to Glue on a Patch (2020)
(AIRE)
5. Mercury QCARE - Quicksilver Inflatable Boat Repair and Sales Techniques
(ihartmacz)
6. The Impossible Leak Repair on a Zodiac Inflatable Boat
(GasHopper Inc)

You might also like

Latest Posts

Article information

Author: Corie Satterfield

Last Updated: 10/15/2022

Views: 6379

Rating: 4.1 / 5 (62 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Corie Satterfield

Birthday: 1992-08-19

Address: 850 Benjamin Bridge, Dickinsonchester, CO 68572-0542

Phone: +26813599986666

Job: Sales Manager

Hobby: Table tennis, Soapmaking, Flower arranging, amateur radio, Rock climbing, scrapbook, Horseback riding

Introduction: My name is Corie Satterfield, I am a fancy, perfect, spotless, quaint, fantastic, funny, lucky person who loves writing and wants to share my knowledge and understanding with you.